| Austin Schuh | 41baf20 | 2022-01-01 14:33:40 -0800 | [diff] [blame^] | 1 | /** |
| 2 | ****************************************************************************** |
| 3 | * @file stm32f2xx_hal_conf.h |
| 4 | * @author MCD Application Team |
| 5 | * @brief HAL configuration file. |
| 6 | ****************************************************************************** |
| 7 | * @attention |
| 8 | * |
| 9 | * <h2><center>© Copyright (c) 2017 STMicroelectronics. |
| 10 | * All rights reserved.</center></h2> |
| 11 | * |
| 12 | * This software component is licensed by ST under BSD 3-Clause license, |
| 13 | * the "License"; You may not use this file except in compliance with the |
| 14 | * License. You may obtain a copy of the License at: |
| 15 | * opensource.org/licenses/BSD-3-Clause |
| 16 | * |
| 17 | ****************************************************************************** |
| 18 | */ |
| 19 | |
| 20 | /* Define to prevent recursive inclusion -------------------------------------*/ |
| 21 | #ifndef __STM32F2xx_HAL_CONF_H |
| 22 | #define __STM32F2xx_HAL_CONF_H |
| 23 | |
| 24 | #ifdef __cplusplus |
| 25 | extern "C" { |
| 26 | #endif |
| 27 | |
| 28 | /* Exported types ------------------------------------------------------------*/ |
| 29 | /* Exported constants --------------------------------------------------------*/ |
| 30 | |
| 31 | /* ########################## Module Selection ############################## */ |
| 32 | /** |
| 33 | * @brief This is the list of modules to be used in the HAL driver |
| 34 | */ |
| 35 | #define HAL_MODULE_ENABLED |
| 36 | /* #define HAL_ADC_MODULE_ENABLED */ |
| 37 | /* #define HAL_CAN_MODULE_ENABLED */ |
| 38 | /* #define HAL_CRC_MODULE_ENABLED */ |
| 39 | /* #define HAL_CRYP_MODULE_ENABLED */ |
| 40 | /* #define HAL_DAC_MODULE_ENABLED */ |
| 41 | /* #define HAL_DCMI_MODULE_ENABLED */ |
| 42 | /* #define HAL_DMA_MODULE_ENABLED */ |
| 43 | /* #define HAL_ETH_MODULE_ENABLED */ |
| 44 | #define HAL_EXTI_MODULE_ENABLED |
| 45 | #define HAL_FLASH_MODULE_ENABLED |
| 46 | /* #define HAL_NAND_MODULE_ENABLED */ |
| 47 | /* #define HAL_NOR_MODULE_ENABLED */ |
| 48 | /* #define HAL_PCCARD_MODULE_ENABLED */ |
| 49 | /* #define HAL_SRAM_MODULE_ENABLED */ |
| 50 | /* #define HAL_HASH_MODULE_ENABLED */ |
| 51 | #define HAL_GPIO_MODULE_ENABLED |
| 52 | /* #define HAL_I2C_MODULE_ENABLED */ |
| 53 | /* #define HAL_I2S_MODULE_ENABLED */ |
| 54 | /* #define HAL_IWDG_MODULE_ENABLED */ |
| 55 | #define HAL_PWR_MODULE_ENABLED |
| 56 | #define HAL_RCC_MODULE_ENABLED |
| 57 | /* #define HAL_RNG_MODULE_ENABLED */ |
| 58 | /* #define HAL_RTC_MODULE_ENABLED */ |
| 59 | /* #define HAL_SD_MODULE_ENABLED */ |
| 60 | /* #define HAL_SPI_MODULE_ENABLED */ |
| 61 | /* #define HAL_TIM_MODULE_ENABLED */ |
| 62 | /* #define HAL_UART_MODULE_ENABLED */ |
| 63 | /* #define HAL_USART_MODULE_ENABLED */ |
| 64 | /* #define HAL_IRDA_MODULE_ENABLED */ |
| 65 | /* #define HAL_SMARTCARD_MODULE_ENABLED */ |
| 66 | /* #define HAL_WWDG_MODULE_ENABLED */ |
| 67 | #define HAL_CORTEX_MODULE_ENABLED |
| 68 | #define HAL_PCD_MODULE_ENABLED |
| 69 | /* #define HAL_HCD_MODULE_ENABLED */ |
| 70 | |
| 71 | |
| 72 | /* ########################## HSE/HSI Values adaptation ##################### */ |
| 73 | /** |
| 74 | * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. |
| 75 | * This value is used by the RCC HAL module to compute the system frequency |
| 76 | * (when HSE is used as system clock source, directly or through the PLL). |
| 77 | */ |
| 78 | #if !defined (HSE_VALUE) |
| 79 | #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ |
| 80 | #endif /* HSE_VALUE */ |
| 81 | |
| 82 | #if !defined (HSE_STARTUP_TIMEOUT) |
| 83 | #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ |
| 84 | #endif /* HSE_STARTUP_TIMEOUT */ |
| 85 | |
| 86 | /** |
| 87 | * @brief Internal High Speed oscillator (HSI) value. |
| 88 | * This value is used by the RCC HAL module to compute the system frequency |
| 89 | * (when HSI is used as system clock source, directly or through the PLL). |
| 90 | */ |
| 91 | #if !defined (HSI_VALUE) |
| 92 | #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz*/ |
| 93 | #endif /* HSI_VALUE */ |
| 94 | |
| 95 | /** |
| 96 | * @brief Internal Low Speed oscillator (LSI) value. |
| 97 | */ |
| 98 | #if !defined (LSI_VALUE) |
| 99 | #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz*/ |
| 100 | #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz |
| 101 | The real value may vary depending on the variations |
| 102 | in voltage and temperature.*/ |
| 103 | /** |
| 104 | * @brief External Low Speed oscillator (LSE) value. |
| 105 | */ |
| 106 | #if !defined (LSE_VALUE) |
| 107 | #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ |
| 108 | #endif /* LSE_VALUE */ |
| 109 | |
| 110 | #if !defined (LSE_STARTUP_TIMEOUT) |
| 111 | #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ |
| 112 | #endif /* LSE_STARTUP_TIMEOUT */ |
| 113 | |
| 114 | /** |
| 115 | * @brief External clock source for I2S peripheral |
| 116 | * This value is used by the I2S HAL module to compute the I2S clock source |
| 117 | * frequency, this source is inserted directly through I2S_CKIN pad. |
| 118 | */ |
| 119 | #if !defined (EXTERNAL_CLOCK_VALUE) |
| 120 | #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the Internal oscillator in Hz*/ |
| 121 | #endif /* EXTERNAL_CLOCK_VALUE */ |
| 122 | |
| 123 | /* Tip: To avoid modifying this file each time you need to use different HSE, |
| 124 | === you can define the HSE value in your toolchain compiler preprocessor. */ |
| 125 | |
| 126 | /* ########################### System Configuration ######################### */ |
| 127 | /** |
| 128 | * @brief This is the HAL system configuration section |
| 129 | */ |
| 130 | #define VDD_VALUE 3300U /*!< Value of VDD in mv */ |
| 131 | #define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ |
| 132 | #define USE_RTOS 0U |
| 133 | #define PREFETCH_ENABLE 1U |
| 134 | #define INSTRUCTION_CACHE_ENABLE 1U |
| 135 | #define DATA_CACHE_ENABLE 1U |
| 136 | |
| 137 | #define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ |
| 138 | #define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ |
| 139 | #define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ |
| 140 | #define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ |
| 141 | #define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ |
| 142 | #define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ |
| 143 | #define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ |
| 144 | #define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ |
| 145 | #define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ |
| 146 | #define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ |
| 147 | #define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ |
| 148 | #define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ |
| 149 | #define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ |
| 150 | #define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ |
| 151 | #define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ |
| 152 | #define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ |
| 153 | #define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ |
| 154 | #define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ |
| 155 | #define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ |
| 156 | #define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ |
| 157 | #define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ |
| 158 | #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ |
| 159 | #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ |
| 160 | #define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ |
| 161 | #define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ |
| 162 | #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ |
| 163 | |
| 164 | /* ########################## Assert Selection ############################## */ |
| 165 | /** |
| 166 | * @brief Uncomment the line below to expanse the "assert_param" macro in the |
| 167 | * HAL drivers code |
| 168 | */ |
| 169 | /* #define USE_FULL_ASSERT 1U */ |
| 170 | |
| 171 | /* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */ |
| 172 | |
| 173 | /* Section 1 : Ethernet peripheral configuration */ |
| 174 | |
| 175 | /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ |
| 176 | #define MAC_ADDR0 2U |
| 177 | #define MAC_ADDR1 0U |
| 178 | #define MAC_ADDR2 0U |
| 179 | #define MAC_ADDR3 0U |
| 180 | #define MAC_ADDR4 0U |
| 181 | #define MAC_ADDR5 0U |
| 182 | |
| 183 | /* Definition of the Ethernet driver buffers size and count */ |
| 184 | #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ |
| 185 | #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ |
| 186 | #define ETH_RXBUFNB 5U /* 5 Rx buffers of size ETH_RX_BUF_SIZE */ |
| 187 | #define ETH_TXBUFNB 5U /* 5 Tx buffers of size ETH_TX_BUF_SIZE */ |
| 188 | |
| 189 | /* Section 2: PHY configuration section */ |
| 190 | |
| 191 | /* LAN8742A PHY Address*/ |
| 192 | #define LAN8742A_PHY_ADDRESS 0x00U |
| 193 | /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ |
| 194 | #define PHY_RESET_DELAY 0x000000FFU |
| 195 | /* PHY Configuration delay */ |
| 196 | #define PHY_CONFIG_DELAY 0x00000FFFU |
| 197 | |
| 198 | #define PHY_READ_TO 0x0000FFFFU |
| 199 | #define PHY_WRITE_TO 0x0000FFFFU |
| 200 | |
| 201 | /* Section 3: Common PHY Registers */ |
| 202 | |
| 203 | #define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ |
| 204 | #define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ |
| 205 | |
| 206 | #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ |
| 207 | #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ |
| 208 | #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ |
| 209 | #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ |
| 210 | #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ |
| 211 | #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ |
| 212 | #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ |
| 213 | #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ |
| 214 | #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ |
| 215 | #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ |
| 216 | |
| 217 | #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ |
| 218 | #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ |
| 219 | #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ |
| 220 | |
| 221 | /* Section 4: Extended PHY Registers */ |
| 222 | |
| 223 | #define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */ |
| 224 | |
| 225 | #define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */ |
| 226 | #define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */ |
| 227 | |
| 228 | |
| 229 | #define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */ |
| 230 | #define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */ |
| 231 | |
| 232 | /* ################## SPI peripheral configuration ########################## */ |
| 233 | |
| 234 | /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver |
| 235 | * Activated: CRC code is present inside driver |
| 236 | * Deactivated: CRC code cleaned from driver |
| 237 | */ |
| 238 | |
| 239 | #define USE_SPI_CRC 1U |
| 240 | |
| 241 | /* Includes ------------------------------------------------------------------*/ |
| 242 | /** |
| 243 | * @brief Include module's header file |
| 244 | */ |
| 245 | |
| 246 | #ifdef HAL_RCC_MODULE_ENABLED |
| 247 | #include "stm32f2xx_hal_rcc.h" |
| 248 | #endif /* HAL_RCC_MODULE_ENABLED */ |
| 249 | |
| 250 | #ifdef HAL_GPIO_MODULE_ENABLED |
| 251 | #include "stm32f2xx_hal_gpio.h" |
| 252 | #endif /* HAL_GPIO_MODULE_ENABLED */ |
| 253 | |
| 254 | #ifdef HAL_EXTI_MODULE_ENABLED |
| 255 | #include "stm32f2xx_hal_exti.h" |
| 256 | #endif /* HAL_EXTI_MODULE_ENABLED */ |
| 257 | |
| 258 | #ifdef HAL_DMA_MODULE_ENABLED |
| 259 | #include "stm32f2xx_hal_dma.h" |
| 260 | #endif /* HAL_DMA_MODULE_ENABLED */ |
| 261 | |
| 262 | #ifdef HAL_CORTEX_MODULE_ENABLED |
| 263 | #include "stm32f2xx_hal_cortex.h" |
| 264 | #endif /* HAL_CORTEX_MODULE_ENABLED */ |
| 265 | |
| 266 | #ifdef HAL_ADC_MODULE_ENABLED |
| 267 | #include "stm32f2xx_hal_adc.h" |
| 268 | #endif /* HAL_ADC_MODULE_ENABLED */ |
| 269 | |
| 270 | #ifdef HAL_CAN_MODULE_ENABLED |
| 271 | #include "stm32f2xx_hal_can.h" |
| 272 | #endif /* HAL_CAN_MODULE_ENABLED */ |
| 273 | |
| 274 | #ifdef HAL_CRC_MODULE_ENABLED |
| 275 | #include "stm32f2xx_hal_crc.h" |
| 276 | #endif /* HAL_CRC_MODULE_ENABLED */ |
| 277 | |
| 278 | #ifdef HAL_CRYP_MODULE_ENABLED |
| 279 | #include "stm32f2xx_hal_cryp.h" |
| 280 | #endif /* HAL_CRYP_MODULE_ENABLED */ |
| 281 | |
| 282 | #ifdef HAL_DAC_MODULE_ENABLED |
| 283 | #include "stm32f2xx_hal_dac.h" |
| 284 | #endif /* HAL_DAC_MODULE_ENABLED */ |
| 285 | |
| 286 | #ifdef HAL_DCMI_MODULE_ENABLED |
| 287 | #include "stm32f2xx_hal_dcmi.h" |
| 288 | #endif /* HAL_DCMI_MODULE_ENABLED */ |
| 289 | |
| 290 | #ifdef HAL_ETH_MODULE_ENABLED |
| 291 | #include "stm32f2xx_hal_eth.h" |
| 292 | #endif /* HAL_ETH_MODULE_ENABLED */ |
| 293 | |
| 294 | #ifdef HAL_FLASH_MODULE_ENABLED |
| 295 | #include "stm32f2xx_hal_flash.h" |
| 296 | #endif /* HAL_FLASH_MODULE_ENABLED */ |
| 297 | |
| 298 | #ifdef HAL_SRAM_MODULE_ENABLED |
| 299 | #include "stm32f2xx_hal_sram.h" |
| 300 | #endif /* HAL_SRAM_MODULE_ENABLED */ |
| 301 | |
| 302 | #ifdef HAL_NOR_MODULE_ENABLED |
| 303 | #include "stm32f2xx_hal_nor.h" |
| 304 | #endif /* HAL_NOR_MODULE_ENABLED */ |
| 305 | |
| 306 | #ifdef HAL_NAND_MODULE_ENABLED |
| 307 | #include "stm32f2xx_hal_nand.h" |
| 308 | #endif /* HAL_NAND_MODULE_ENABLED */ |
| 309 | |
| 310 | #ifdef HAL_PCCARD_MODULE_ENABLED |
| 311 | #include "stm32f2xx_hal_pccard.h" |
| 312 | #endif /* HAL_PCCARD_MODULE_ENABLED */ |
| 313 | |
| 314 | #ifdef HAL_HASH_MODULE_ENABLED |
| 315 | #include "stm32f2xx_hal_hash.h" |
| 316 | #endif /* HAL_HASH_MODULE_ENABLED */ |
| 317 | |
| 318 | #ifdef HAL_I2C_MODULE_ENABLED |
| 319 | #include "stm32f2xx_hal_i2c.h" |
| 320 | #endif /* HAL_I2C_MODULE_ENABLED */ |
| 321 | |
| 322 | #ifdef HAL_I2S_MODULE_ENABLED |
| 323 | #include "stm32f2xx_hal_i2s.h" |
| 324 | #endif /* HAL_I2S_MODULE_ENABLED */ |
| 325 | |
| 326 | #ifdef HAL_IWDG_MODULE_ENABLED |
| 327 | #include "stm32f2xx_hal_iwdg.h" |
| 328 | #endif /* HAL_IWDG_MODULE_ENABLED */ |
| 329 | |
| 330 | #ifdef HAL_PWR_MODULE_ENABLED |
| 331 | #include "stm32f2xx_hal_pwr.h" |
| 332 | #endif /* HAL_PWR_MODULE_ENABLED */ |
| 333 | |
| 334 | #ifdef HAL_RNG_MODULE_ENABLED |
| 335 | #include "stm32f2xx_hal_rng.h" |
| 336 | #endif /* HAL_RNG_MODULE_ENABLED */ |
| 337 | |
| 338 | #ifdef HAL_RTC_MODULE_ENABLED |
| 339 | #include "stm32f2xx_hal_rtc.h" |
| 340 | #endif /* HAL_RTC_MODULE_ENABLED */ |
| 341 | |
| 342 | #ifdef HAL_SD_MODULE_ENABLED |
| 343 | #include "stm32f2xx_hal_sd.h" |
| 344 | #endif /* HAL_SD_MODULE_ENABLED */ |
| 345 | |
| 346 | #ifdef HAL_SPI_MODULE_ENABLED |
| 347 | #include "stm32f2xx_hal_spi.h" |
| 348 | #endif /* HAL_SPI_MODULE_ENABLED */ |
| 349 | |
| 350 | #ifdef HAL_TIM_MODULE_ENABLED |
| 351 | #include "stm32f2xx_hal_tim.h" |
| 352 | #endif /* HAL_TIM_MODULE_ENABLED */ |
| 353 | |
| 354 | #ifdef HAL_UART_MODULE_ENABLED |
| 355 | #include "stm32f2xx_hal_uart.h" |
| 356 | #endif /* HAL_UART_MODULE_ENABLED */ |
| 357 | |
| 358 | #ifdef HAL_USART_MODULE_ENABLED |
| 359 | #include "stm32f2xx_hal_usart.h" |
| 360 | #endif /* HAL_USART_MODULE_ENABLED */ |
| 361 | |
| 362 | #ifdef HAL_IRDA_MODULE_ENABLED |
| 363 | #include "stm32f2xx_hal_irda.h" |
| 364 | #endif /* HAL_IRDA_MODULE_ENABLED */ |
| 365 | |
| 366 | #ifdef HAL_SMARTCARD_MODULE_ENABLED |
| 367 | #include "stm32f2xx_hal_smartcard.h" |
| 368 | #endif /* HAL_SMARTCARD_MODULE_ENABLED */ |
| 369 | |
| 370 | #ifdef HAL_WWDG_MODULE_ENABLED |
| 371 | #include "stm32f2xx_hal_wwdg.h" |
| 372 | #endif /* HAL_WWDG_MODULE_ENABLED */ |
| 373 | |
| 374 | #ifdef HAL_PCD_MODULE_ENABLED |
| 375 | #include "stm32f2xx_hal_pcd.h" |
| 376 | #endif /* HAL_PCD_MODULE_ENABLED */ |
| 377 | |
| 378 | #ifdef HAL_HCD_MODULE_ENABLED |
| 379 | #include "stm32f2xx_hal_hcd.h" |
| 380 | #endif /* HAL_HCD_MODULE_ENABLED */ |
| 381 | |
| 382 | /* Exported macro ------------------------------------------------------------*/ |
| 383 | #ifdef USE_FULL_ASSERT |
| 384 | /** |
| 385 | * @brief The assert_param macro is used for function's parameters check. |
| 386 | * @param expr: If expr is false, it calls assert_failed function |
| 387 | * which reports the name of the source file and the source |
| 388 | * line number of the call that failed. |
| 389 | * If expr is true, it returns no value. |
| 390 | * @retval None |
| 391 | */ |
| 392 | #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) |
| 393 | /* Exported functions ------------------------------------------------------- */ |
| 394 | void assert_failed(uint8_t* file, uint32_t line); |
| 395 | #else |
| 396 | #define assert_param(expr) ((void)0U) |
| 397 | #endif /* USE_FULL_ASSERT */ |
| 398 | |
| 399 | |
| 400 | #ifdef __cplusplus |
| 401 | } |
| 402 | #endif |
| 403 | |
| 404 | #endif /* __STM32F2xx_HAL_CONF_H */ |
| 405 | |
| 406 | |
| 407 | /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |