Squashed 'third_party/pico-sdk/lib/tinyusb/' content from commit 868948f67c
Change-Id: I5d33c2566dd597be9d4b1c30d4b3723c5ef4a265
git-subtree-dir: third_party/pico-sdk/lib/tinyusb
git-subtree-split: 868948f67c90fa7c2553cdcd604b52862cf55720
Signed-off-by: Austin Schuh <austin.linux@gmail.com>
diff --git a/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h b/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h
new file mode 100644
index 0000000..2ab46b2
--- /dev/null
+++ b/hw/bsp/stm32f207nucleo/stm32f2xx_hal_conf.h
@@ -0,0 +1,407 @@
+/**
+ ******************************************************************************
+ * @file stm32f2xx_hal_conf.h
+ * @author MCD Application Team
+ * @brief HAL configuration file.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© Copyright (c) 2017 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F2xx_HAL_CONF_H
+#define __STM32F2xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+ * @brief This is the list of modules to be used in the HAL driver
+ */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_CRYP_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+/* #define HAL_DCMI_MODULE_ENABLED */
+/* #define HAL_DMA_MODULE_ENABLED */
+/* #define HAL_ETH_MODULE_ENABLED */
+#define HAL_EXTI_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_PCCARD_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_HASH_MODULE_ENABLED */
+#define HAL_GPIO_MODULE_ENABLED
+/* #define HAL_I2C_MODULE_ENABLED */
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RNG_MODULE_ENABLED */
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+/* #define HAL_SPI_MODULE_ENABLED */
+/* #define HAL_TIM_MODULE_ENABLED */
+/* #define HAL_UART_MODULE_ENABLED */
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED
+#define HAL_PCD_MODULE_ENABLED
+/* #define HAL_HCD_MODULE_ENABLED */
+
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+ * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSE is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief Internal High Speed oscillator (HSI) value.
+ * This value is used by the RCC HAL module to compute the system frequency
+ * (when HSI is used as system clock source, directly or through the PLL).
+ */
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief Internal Low Speed oscillator (LSI) value.
+ */
+#if !defined (LSI_VALUE)
+ #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz*/
+#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
+ The real value may vary depending on the variations
+ in voltage and temperature.*/
+/**
+ * @brief External Low Speed oscillator (LSE) value.
+ */
+#if !defined (LSE_VALUE)
+ #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined (LSE_STARTUP_TIMEOUT)
+ #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+ * @brief External clock source for I2S peripheral
+ * This value is used by the I2S HAL module to compute the I2S clock source
+ * frequency, this source is inserted directly through I2S_CKIN pad.
+ */
+#if !defined (EXTERNAL_CLOCK_VALUE)
+ #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the Internal oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+ === you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+ * @brief This is the HAL system configuration section
+ */
+#define VDD_VALUE 3300U /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 1U
+#define INSTRUCTION_CACHE_ENABLE 1U
+#define DATA_CACHE_ENABLE 1U
+
+#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */
+#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */
+#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */
+#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */
+#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */
+#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */
+#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */
+#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */
+#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */
+#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */
+#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */
+#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */
+#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */
+#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */
+#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */
+#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */
+#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */
+#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */
+#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */
+#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */
+#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */
+#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */
+#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */
+#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */
+#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */
+#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */
+
+/* ########################## Assert Selection ############################## */
+/**
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * HAL drivers code
+ */
+/* #define USE_FULL_ASSERT 1U */
+
+/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0 2U
+#define MAC_ADDR1 0U
+#define MAC_ADDR2 0U
+#define MAC_ADDR3 0U
+#define MAC_ADDR4 0U
+#define MAC_ADDR5 0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
+#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
+#define ETH_RXBUFNB 5U /* 5 Rx buffers of size ETH_RX_BUF_SIZE */
+#define ETH_TXBUFNB 5U /* 5 Tx buffers of size ETH_TX_BUF_SIZE */
+
+/* Section 2: PHY configuration section */
+
+/* LAN8742A PHY Address*/
+#define LAN8742A_PHY_ADDRESS 0x00U
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY 0x000000FFU
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY 0x00000FFFU
+
+#define PHY_READ_TO 0x0000FFFFU
+#define PHY_WRITE_TO 0x0000FFFFU
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */
+#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */
+
+#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
+#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
+#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
+#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
+#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
+#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
+#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
+
+#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
+#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
+#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */
+
+#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */
+#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */
+
+
+#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */
+#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC 1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+ * @brief Include module's header file
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f2xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f2xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+ #include "stm32f2xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+ #include "stm32f2xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f2xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f2xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f2xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f2xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+ #include "stm32f2xx_hal_cryp.h"
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f2xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+ #include "stm32f2xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+ #include "stm32f2xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f2xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+ #include "stm32f2xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+ #include "stm32f2xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+ #include "stm32f2xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+ #include "stm32f2xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f2xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f2xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f2xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f2xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f2xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f2xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f2xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f2xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f2xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f2xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f2xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f2xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f2xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f2xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f2xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f2xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f2xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef USE_FULL_ASSERT
+/**
+ * @brief The assert_param macro is used for function's parameters check.
+ * @param expr: If expr is false, it calls assert_failed function
+ * which reports the name of the source file and the source
+ * line number of the call that failed.
+ * If expr is true, it returns no value.
+ * @retval None
+ */
+ #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+ void assert_failed(uint8_t* file, uint32_t line);
+#else
+ #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F2xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/