| Brian Silverman | 2df8441 | 2013-12-10 14:00:40 -0800 | [diff] [blame^] | 1 | EXTI interrupt groupings: |
| 2 | by number in the port |
| 3 | 0,1,2,3,4,5-9,10-15 |
| 4 | |
| 5 | |
| 6 | PA0 TIM5.1 |
| 7 | PA1 TIM5.2 |
| 8 | PA2 |
| 9 | PA3 |
| 10 | PA4 SPI3_NSS (slave select) |
| 11 | PA5 TIM2.1 |
| 12 | PA6 TIM3.1 |
| 13 | PA7 |
| 14 | PA8 TIM1.1 |
| 15 | PA9 USART1_TX (bootloader) |
| 16 | PA10 USART1_RX (bootloader) |
| 17 | PA11 (don't change during reset into bootloader) |
| 18 | PA12 (don't change during reset into bootloader) |
| 19 | PA13 SWDIO |
| 20 | PA14 SWCLK |
| 21 | PA15 (gets pulled up during reset (JTAG pin)) |
| 22 | PB0 TIM1.2 |
| 23 | PB1 |
| 24 | PB2 BOOT1 (tie to GND) |
| 25 | PB3 TIM2.2 |
| 26 | PB4 (gets pulled up during reset (JTAG pin)) |
| 27 | PB5 TIM3.2 (don't change during reset into bootloader) |
| 28 | PB6 TIM4.1 |
| 29 | PB7 TIM4.2 |
| 30 | PB8 |
| 31 | PB9 |
| 32 | PB10 |
| 33 | PB11 (don't change during reset into bootloader) |
| 34 | PB12 SPI2_NSS (slave select) |
| 35 | PB13 SPI2_SCK |
| 36 | PB14 SPI2_MISO |
| 37 | PB15 SPI2_MOSI |
| 38 | PC0 |
| 39 | PC1 |
| 40 | PC2 |
| 41 | PC3 |
| 42 | PC4 |
| 43 | PC5 |
| 44 | PC6 TIM8.1 |
| 45 | PC7 TIM8.2 |
| 46 | PC8 |
| 47 | PC9 |
| 48 | PC10 SPI3_SCK |
| 49 | PC11 SPI3_MISO |
| 50 | PC12 SPI3_MOSI |
| 51 | PC13 |
| 52 | PC14 |
| 53 | PC15 |
| 54 | PD2 |
| 55 | |
| 56 | [GPIOs] |
| 57 | C0 enc |
| 58 | C1 enc |
| 59 | A2 enc |
| 60 | A3 enc |
| 61 | |
| 62 | B2 |
| 63 | #A2 TIM9.1 |
| 64 | C4 |
| 65 | C5 |
| 66 | A7 |
| 67 | B8 |
| 68 | B9 |
| 69 | B10 |
| 70 | A11 |
| 71 | A12 |
| 72 | C13 |
| 73 | C14 |
| 74 | C15 |
| 75 | |
| 76 | C8 BBB_RST TIM8.3 |
| 77 | |
| 78 | |
| 79 | IO compensation cell? |
| 80 | controls slew rates |
| 81 | increased power draw |
| 82 | should probably just enable it? |