hw/bsp/stm32l4/boards/stm32l476disco/board.h

/* 
 * The MIT License (MIT)
 *
 * Copyright (c) 2020, Ha Thach (tinyusb.org)
 *
 * Permission is hereby granted, free of charge, to any person obtaining a copy
 * of this software and associated documentation files (the "Software"), to deal
 * in the Software without restriction, including without limitation the rights
 * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
 * copies of the Software, and to permit persons to whom the Software is
 * furnished to do so, subject to the following conditions:
 *
 * The above copyright notice and this permission notice shall be included in
 * all copies or substantial portions of the Software.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
 * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
 * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
 * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
 * THE SOFTWARE.
 *
 * This file is part of the TinyUSB stack.
 */

#ifndef BOARD_H_
#define BOARD_H_

#ifdef __cplusplus
 extern "C" {
#endif

#define LED_PORT              GPIOB
#define LED_PIN               GPIO_PIN_2
#define LED_STATE_ON          1

#define BUTTON_PORT           GPIOA
#define BUTTON_PIN            GPIO_PIN_0
#define BUTTON_STATE_ACTIVE   1

#define UART_DEV              USART2
#define UART_CLK_EN           __HAL_RCC_USART2_CLK_ENABLE
#define UART_GPIO_PORT        GPIOD
#define UART_GPIO_AF          GPIO_AF7_USART2
#define UART_TX_PIN           GPIO_PIN_5
#define UART_RX_PIN           GPIO_PIN_6

//--------------------------------------------------------------------+
// RCC Clock
//--------------------------------------------------------------------+

/**
  * @brief  System Clock Configuration
  *         The system Clock is configured as follow :
  *
  *         If define USB_USE_LSE_MSI_CLOCK enabled:
  *            System Clock source            = PLL (MSI)
  *            SYSCLK(Hz)                     = 80000000
  *            HCLK(Hz)                       = 80000000
  *            AHB Prescaler                  = 1
  *            APB1 Prescaler                 = 1
  *            APB2 Prescaler                 = 2
  *            MSI Frequency(Hz)              = 4800000
  *            LSE Frequency(Hz)              = 32768
  *            PLL_M                          = 6
  *            PLL_N                          = 40
  *            PLL_P                          = 7
  *            PLL_Q                          = 4
  *            PLL_R                          = 4
  *            Flash Latency(WS)              = 4
  * @param  None
  * @retval None
  */
static inline void board_clock_init(void)
{
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_OscInitTypeDef RCC_OscInitStruct;
  RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;

  /* Enable the LSE Oscillator */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSE;
  RCC_OscInitStruct.LSEState = RCC_LSE_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);

  /* Enable the CSS interrupt in case LSE signal is corrupted or not present */
  HAL_RCCEx_DisableLSECSS();

  /* Set tick interrupt priority, default HAL value is intentionally invalid
     and that prevents PLL initialization in HAL_RCC_OscConfig() */
  HAL_InitTick((1UL << __NVIC_PRIO_BITS) - 1UL);

  /* Enable MSI Oscillator and activate PLL with MSI as source */
  RCC_OscInitStruct.OscillatorType      = RCC_OSCILLATORTYPE_MSI;
  RCC_OscInitStruct.MSIState            = RCC_MSI_ON;
  RCC_OscInitStruct.MSICalibrationValue = RCC_MSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.MSIClockRange       = RCC_MSIRANGE_11;
  RCC_OscInitStruct.PLL.PLLState        = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource       = RCC_PLLSOURCE_MSI;
  RCC_OscInitStruct.PLL.PLLM            = 6;
  RCC_OscInitStruct.PLL.PLLN            = 40;
  RCC_OscInitStruct.PLL.PLLP            = 7;
  RCC_OscInitStruct.PLL.PLLQ            = 4;
  RCC_OscInitStruct.PLL.PLLR            = 4;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);

  /* Enable MSI Auto-calibration through LSE */
  HAL_RCCEx_EnableMSIPLLMode();

  /* Select MSI output as USB clock source */
  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB;
  PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_MSI;
  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);

  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
  clocks dividers */
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4);
}

static inline void board_vbus_sense_init(void)
{
  // L476Disco use general GPIO PC11 for VBUS sensing instead of dedicated PA9 as others
  // Disable VBUS Sense and force device mode
  USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBDEN;

  USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN | USB_OTG_GOTGCTL_BVALOVAL;
}

#ifdef __cplusplus
 }
#endif

#endif /* BOARD_H_ */