Squashed 'third_party/pico-sdk/lib/tinyusb/' content from commit 868948f67c
Change-Id: I5d33c2566dd597be9d4b1c30d4b3723c5ef4a265
git-subtree-dir: third_party/pico-sdk/lib/tinyusb
git-subtree-split: 868948f67c90fa7c2553cdcd604b52862cf55720
Signed-off-by: Austin Schuh <austin.linux@gmail.com>
diff --git a/hw/bsp/stm32h7/boards/stm32h743eval/board.h b/hw/bsp/stm32h7/boards/stm32h743eval/board.h
new file mode 100644
index 0000000..af2063c
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/stm32h743eval/board.h
@@ -0,0 +1,143 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2021, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#define LED_PORT GPIOA
+#define LED_PIN GPIO_PIN_4
+#define LED_STATE_ON 1
+
+// Tamper push-button
+#define BUTTON_PORT GPIOC
+#define BUTTON_PIN GPIO_PIN_13
+#define BUTTON_STATE_ACTIVE 0
+
+// Need to change jumper setting J7 and J8 from RS-232 to STLink
+#define UART_DEV USART1
+#define UART_CLK_EN __HAL_RCC_USART1_CLK_ENABLE
+#define UART_GPIO_PORT GPIOB
+#define UART_GPIO_AF GPIO_AF4_USART1
+#define UART_TX_PIN GPIO_PIN_14
+#define UART_RX_PIN GPIO_PIN_15
+
+// VBUS Sense detection
+#define OTG_FS_VBUS_SENSE 1
+#define OTG_HS_VBUS_SENSE 0
+
+// USB HS External PHY Pin: CLK, STP, DIR, NXT, D0-D7
+#define ULPI_PINS \
+ {GPIOA, GPIO_PIN_3 }, {GPIOA, GPIO_PIN_5 }, {GPIOB, GPIO_PIN_0 }, {GPIOB, GPIO_PIN_1 }, \
+ {GPIOB, GPIO_PIN_5 }, {GPIOB, GPIO_PIN_10}, {GPIOB, GPIO_PIN_11}, {GPIOB, GPIO_PIN_12}, \
+ {GPIOB, GPIO_PIN_13}, {GPIOC, GPIO_PIN_0 }, {GPIOH, GPIO_PIN_4 }, {GPIOI, GPIO_PIN_11}
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32h7_clock_init(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /*!< Supply configuration update enable */
+ HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY);
+
+ /* The voltage scaling allows optimizing the power consumption when the device is
+ clocked below the maximum system frequency, to update the voltage scaling value
+ regarding system frequency refer to product datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ while ((PWR->D3CR & (PWR_D3CR_VOSRDY)) != PWR_D3CR_VOSRDY) {}
+
+ /* Enable HSE Oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
+ RCC_OscInitStruct.CSIState = RCC_CSI_OFF;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+
+ /* PLL1 for System Clock */
+ RCC_OscInitStruct.PLL.PLLM = 5;
+ RCC_OscInitStruct.PLL.PLLN = 160;
+ RCC_OscInitStruct.PLL.PLLFRACN = 0;
+ RCC_OscInitStruct.PLL.PLLP = 2;
+ RCC_OscInitStruct.PLL.PLLR = 2;
+ RCC_OscInitStruct.PLL.PLLQ = 4;
+
+ RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOMEDIUM;
+ RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* PLL3 for USB Clock */
+ PeriphClkInitStruct.PLL3.PLL3M = 25;
+ PeriphClkInitStruct.PLL3.PLL3N = 336;
+ PeriphClkInitStruct.PLL3.PLL3FRACN = 0;
+ PeriphClkInitStruct.PLL3.PLL3P = 2;
+ PeriphClkInitStruct.PLL3.PLL3R = 2;
+ PeriphClkInitStruct.PLL3.PLL3Q = 7;
+
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB;
+ PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL3;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure bus clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_D1PCLK1 | RCC_CLOCKTYPE_PCLK1 | \
+ RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_D3PCLK1);
+
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2;
+ RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV1;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4);
+
+ /*activate CSI clock mondatory for I/O Compensation Cell*/
+ __HAL_RCC_CSI_ENABLE() ;
+
+ /* Enable SYSCFG clock mondatory for I/O Compensation Cell */
+ __HAL_RCC_SYSCFG_CLK_ENABLE() ;
+
+ /* Enables the I/O Compensation Cell */
+ HAL_EnableCompensationCell();
+}
+
+static inline void board_stm32h7_post_init(void)
+{
+ // For this board does nothing
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif
diff --git a/hw/bsp/stm32h7/boards/stm32h743eval/board.mk b/hw/bsp/stm32h7/boards/stm32h743eval/board.mk
new file mode 100644
index 0000000..b768a0e
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/stm32h743eval/board.mk
@@ -0,0 +1,14 @@
+CFLAGS += -DSTM32H743xx -DHSE_VALUE=25000000
+
+# Default is Highspeed port
+PORT ?= 1
+SPEED ?= high
+
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s
+LD_FILE = $(BOARD_PATH)/stm32h743xx_flash.ld
+
+# For flash-jlink target
+JLINK_DEVICE = stm32h743xi
+
+# flash target using on-board stlink
+flash: flash-stlink
diff --git a/hw/bsp/stm32h7/boards/stm32h743eval/stm32h743xx_flash.ld b/hw/bsp/stm32h7/boards/stm32h743eval/stm32h743xx_flash.ld
new file mode 100644
index 0000000..59b9ff4
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/stm32h743eval/stm32h743xx_flash.ld
@@ -0,0 +1,173 @@
+/*
+*****************************************************************************
+**
+
+** File : LinkerScript.ld
+**
+** Abstract : Linker script for STM32H743XIHx Device with
+** 2048KByte FLASH, 128KByte RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+**
+** Distribution: The file is distributed as is, without any warranty
+** of any kind.
+**
+** (c)Copyright Ac6.
+** You may use this file as-is or modify it according to the needs of your
+** project. Distribution of this file (unmodified or modified) is not
+** permitted. Ac6 permit registered System Workbench for MCU users the
+** rights to distribute the assembled, compiled & linked contents of this
+** file as part of an application binary file, provided that it is built
+** using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20020000; /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+DTCMRAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K
+RAM_D1 (xrw) : ORIGIN = 0x24000000, LENGTH = 512K
+RAM_D2 (xrw) : ORIGIN = 0x30000000, LENGTH = 288K
+RAM_D3 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K
+ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K
+FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 2048K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >DTCMRAM AT> FLASH
+
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >DTCMRAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >DTCMRAM
+
+
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
+
+
diff --git a/hw/bsp/stm32h7/boards/stm32h743nucleo/board.h b/hw/bsp/stm32h7/boards/stm32h743nucleo/board.h
new file mode 100644
index 0000000..06148c8
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/stm32h743nucleo/board.h
@@ -0,0 +1,122 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2021, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#define LED_PORT GPIOB
+#define LED_PIN GPIO_PIN_0
+#define LED_STATE_ON 1
+
+#define BUTTON_PORT GPIOC
+#define BUTTON_PIN GPIO_PIN_13
+#define BUTTON_STATE_ACTIVE 1
+
+#define UART_DEV USART3
+#define UART_CLK_EN __HAL_RCC_USART3_CLK_ENABLE
+#define UART_GPIO_PORT GPIOD
+#define UART_GPIO_AF GPIO_AF7_USART3
+#define UART_TX_PIN GPIO_PIN_8
+#define UART_RX_PIN GPIO_PIN_9
+
+// VBUS Sense detection
+#define OTG_FS_VBUS_SENSE 1
+#define OTG_HS_VBUS_SENSE 0
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32h7_clock_init(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+
+ /* The PWR block is always enabled on the H7 series- there is no clock
+ enable. For now, use the default VOS3 scale mode (lowest) and limit clock
+ frequencies to avoid potential current draw problems from bus
+ power when using the max clock speeds throughout the chip. */
+
+ /* Enable HSE Oscillator and activate PLL1 with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
+ RCC_OscInitStruct.CSIState = RCC_CSI_OFF;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000;
+ RCC_OscInitStruct.PLL.PLLN = 336;
+ RCC_OscInitStruct.PLL.PLLP = 2;
+ RCC_OscInitStruct.PLL.PLLQ = 7;
+ RCC_OscInitStruct.PLL.PLLR = 2; /* Unused */
+ RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_0;
+ RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOMEDIUM;
+ RCC_OscInitStruct.PLL.PLLFRACN = 0;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | \
+ RCC_CLOCKTYPE_D1PCLK1 | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | \
+ RCC_CLOCKTYPE_D3PCLK1);
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV1;
+
+ /* Unlike on the STM32F4 family, it appears the maximum APB frequencies are
+ device-dependent- 120 MHz for this board according to Figure 2 of
+ the datasheet. Dividing by half will be safe for now. */
+ RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV2;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2;
+ RCC_ClkInitStruct.APB4CLKDivider = RCC_APB4_DIV2;
+
+ /* 4 wait states required for 168MHz and VOS3. */
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4);
+
+ /* Like on F4, on H7, USB's actual peripheral clock and bus clock are
+ separate. However, the main system PLL (PLL1) doesn't have a direct
+ connection to the USB peripheral clock to generate 48 MHz, so we do this
+ dance. This will connect PLL1's Q output to the USB peripheral clock. */
+ RCC_PeriphCLKInitTypeDef RCC_PeriphCLKInitStruct;
+
+ RCC_PeriphCLKInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB;
+ RCC_PeriphCLKInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL;
+ HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphCLKInitStruct);
+}
+
+static inline void board_stm32h7_post_init(void)
+{
+ // For this board does nothing
+}
+
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif
diff --git a/hw/bsp/stm32h7/boards/stm32h743nucleo/board.mk b/hw/bsp/stm32h7/boards/stm32h743nucleo/board.mk
new file mode 100644
index 0000000..fc670fe
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/stm32h743nucleo/board.mk
@@ -0,0 +1,13 @@
+CFLAGS += -DSTM32H743xx -DHSE_VALUE=8000000
+
+# Default is FulSpeed port
+PORT ?= 0
+
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s
+LD_FILE = $(BOARD_PATH)/stm32h743xx_flash.ld
+
+# For flash-jlink target
+JLINK_DEVICE = stm32h743zi
+
+# flash target using on-board stlink
+flash: flash-stlink
diff --git a/hw/bsp/stm32h7/boards/stm32h743nucleo/stm32h743xx_flash.ld b/hw/bsp/stm32h7/boards/stm32h743nucleo/stm32h743xx_flash.ld
new file mode 100644
index 0000000..59b9ff4
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/stm32h743nucleo/stm32h743xx_flash.ld
@@ -0,0 +1,173 @@
+/*
+*****************************************************************************
+**
+
+** File : LinkerScript.ld
+**
+** Abstract : Linker script for STM32H743XIHx Device with
+** 2048KByte FLASH, 128KByte RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+**
+** Distribution: The file is distributed as is, without any warranty
+** of any kind.
+**
+** (c)Copyright Ac6.
+** You may use this file as-is or modify it according to the needs of your
+** project. Distribution of this file (unmodified or modified) is not
+** permitted. Ac6 permit registered System Workbench for MCU users the
+** rights to distribute the assembled, compiled & linked contents of this
+** file as part of an application binary file, provided that it is built
+** using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20020000; /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200; /* required amount of heap */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+DTCMRAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K
+RAM_D1 (xrw) : ORIGIN = 0x24000000, LENGTH = 512K
+RAM_D2 (xrw) : ORIGIN = 0x30000000, LENGTH = 288K
+RAM_D3 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K
+ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K
+FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 2048K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >DTCMRAM AT> FLASH
+
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >DTCMRAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >DTCMRAM
+
+
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
+
+
diff --git a/hw/bsp/stm32h7/boards/stm32h745disco/board.h b/hw/bsp/stm32h7/boards/stm32h745disco/board.h
new file mode 100644
index 0000000..d33e0c8
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/stm32h745disco/board.h
@@ -0,0 +1,139 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2021, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#define LED_PORT GPIOJ
+#define LED_PIN GPIO_PIN_2
+#define LED_STATE_ON 1
+
+// Blue push-button
+#define BUTTON_PORT GPIOC
+#define BUTTON_PIN GPIO_PIN_13
+#define BUTTON_STATE_ACTIVE 1
+
+// UART
+#define UART_DEV USART3
+#define UART_CLK_EN __HAL_RCC_USART3_CLK_ENABLE
+#define UART_GPIO_PORT GPIOB
+#define UART_GPIO_AF GPIO_AF7_USART3
+#define UART_TX_PIN GPIO_PIN_10
+#define UART_RX_PIN GPIO_PIN_11
+
+// VBUS Sense detection
+#define OTG_FS_VBUS_SENSE 1
+#define OTG_HS_VBUS_SENSE 0
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32h7_clock_init(void)
+{
+ RCC_ClkInitTypeDef RCC_ClkInitStruct;
+ RCC_OscInitTypeDef RCC_OscInitStruct;
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;
+
+ /*!< Supply configuration update enable */
+ /* For STM32H750XB, use "HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY);" */
+ HAL_PWREx_ConfigSupply(PWR_DIRECT_SMPS_SUPPLY);
+
+ /* The voltage scaling allows optimizing the power consumption when the
+ device is clocked below the maximum system frequency, to update the
+ voltage scaling value regarding system frequency refer to product
+ datasheet. */
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+ while ((PWR->D3CR & (PWR_D3CR_VOSRDY)) != PWR_D3CR_VOSRDY) {}
+
+ /* Enable HSE Oscillator and activate PLL with HSE as source */
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
+ RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
+ RCC_OscInitStruct.CSIState = RCC_CSI_OFF;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+
+ /* PLL1 for System Clock */
+ RCC_OscInitStruct.PLL.PLLM = 5;
+ RCC_OscInitStruct.PLL.PLLN = 160;
+ RCC_OscInitStruct.PLL.PLLFRACN = 0;
+ RCC_OscInitStruct.PLL.PLLP = 2;
+ RCC_OscInitStruct.PLL.PLLR = 2;
+ RCC_OscInitStruct.PLL.PLLQ = 4;
+
+ RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOMEDIUM;
+ RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ /* PLL3 for USB Clock */
+ PeriphClkInitStruct.PLL3.PLL3M = 25;
+ PeriphClkInitStruct.PLL3.PLL3N = 336;
+ PeriphClkInitStruct.PLL3.PLL3FRACN = 0;
+ PeriphClkInitStruct.PLL3.PLL3P = 2;
+ PeriphClkInitStruct.PLL3.PLL3R = 2;
+ PeriphClkInitStruct.PLL3.PLL3Q = 7;
+
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB;
+ PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL3;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ /* Select PLL as system clock source and configure bus clocks dividers */
+ RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_D1PCLK1 | RCC_CLOCKTYPE_PCLK1 | \
+ RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_D3PCLK1);
+
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2;
+ RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV1;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4);
+
+ /*activate CSI clock mondatory for I/O Compensation Cell*/
+ __HAL_RCC_CSI_ENABLE() ;
+
+ /* Enable SYSCFG clock mondatory for I/O Compensation Cell */
+ __HAL_RCC_SYSCFG_CLK_ENABLE() ;
+
+ /* Enables the I/O Compensation Cell */
+ HAL_EnableCompensationCell();
+}
+
+static inline void board_stm32h7_post_init(void)
+{
+ // For this board does nothing
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif
diff --git a/hw/bsp/stm32h7/boards/stm32h745disco/board.mk b/hw/bsp/stm32h7/boards/stm32h745disco/board.mk
new file mode 100644
index 0000000..384065b
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/stm32h745disco/board.mk
@@ -0,0 +1,17 @@
+# STM32H745I-DISCO uses OTG_FS
+# FIXME: Reset enumerates, un/replug USB plug does not enumerate
+
+CFLAGS += -DSTM32H745xx -DCORE_CM7 -DHSE_VALUE=25000000
+
+# Default is FulSpeed port
+PORT ?= 0
+
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h745xx.s
+LD_FILE = $(ST_CMSIS)/Source/Templates/gcc/linker/stm32h745xx_flash_CM7.ld
+
+# For flash-jlink target
+JLINK_DEVICE = stm32h745xi_m7
+
+# flash target using on-board stlink
+flash: flash-stlink
+
diff --git a/hw/bsp/stm32h7/boards/waveshare_openh743i/STM32H743IITX_FLASH.ld b/hw/bsp/stm32h7/boards/waveshare_openh743i/STM32H743IITX_FLASH.ld
new file mode 100644
index 0000000..73d2ded
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/waveshare_openh743i/STM32H743IITX_FLASH.ld
@@ -0,0 +1,175 @@
+/*
+******************************************************************************
+**
+** File : LinkerScript.ld
+**
+** Author : STM32CubeIDE
+**
+** Abstract : Linker script for STM32H7 series
+** 2048Kbytes FLASH and 192Kbytes RAM
+**
+** Set heap size, stack size and stack location according
+** to application requirements.
+**
+** Set memory bank area and size if external memory is used.
+**
+** Target : STMicroelectronics STM32
+**
+** Distribution: The file is distributed as is, without any warranty
+** of any kind.
+**
+*****************************************************************************
+** @attention
+**
+** Copyright (c) 2019 STMicroelectronics.
+** All rights reserved.
+**
+** This software component is licensed by ST under BSD 3-Clause license,
+** the "License"; You may not use this file except in compliance with the
+** License. You may obtain a copy of the License at:
+** opensource.org/licenses/BSD-3-Clause
+**
+****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20020000; /* end of RAM */
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x2000 ; /* required amount of heap */
+_Min_Stack_Size = 0x2000 ; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+ FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 2048K
+ RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K
+ RAM_D1 (xrw) : ORIGIN = 0x24000000, LENGTH = 512K
+ RAM_D2 (xrw) : ORIGIN = 0x30000000, LENGTH = 288K
+ RAM_D3 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K
+ ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K
+}
+
+/* Define output sections */
+SECTIONS
+{
+ /* The startup code goes first into FLASH */
+ .isr_vector :
+ {
+ . = ALIGN(4);
+ KEEP(*(.isr_vector)) /* Startup code */
+ . = ALIGN(4);
+ } >FLASH
+
+ /* The program code and other data goes into FLASH */
+ .text :
+ {
+ . = ALIGN(4);
+ *(.text) /* .text sections (code) */
+ *(.text*) /* .text* sections (code) */
+ *(.glue_7) /* glue arm to thumb code */
+ *(.glue_7t) /* glue thumb to arm code */
+ *(.eh_frame)
+
+ KEEP (*(.init))
+ KEEP (*(.fini))
+
+ . = ALIGN(4);
+ _etext = .; /* define a global symbols at end of code */
+ } >FLASH
+
+ /* Constant data goes into FLASH */
+ .rodata :
+ {
+ . = ALIGN(4);
+ *(.rodata) /* .rodata sections (constants, strings, etc.) */
+ *(.rodata*) /* .rodata* sections (constants, strings, etc.) */
+ . = ALIGN(4);
+ } >FLASH
+
+ .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+ .ARM : {
+ __exidx_start = .;
+ *(.ARM.exidx*)
+ __exidx_end = .;
+ } >FLASH
+
+ .preinit_array :
+ {
+ PROVIDE_HIDDEN (__preinit_array_start = .);
+ KEEP (*(.preinit_array*))
+ PROVIDE_HIDDEN (__preinit_array_end = .);
+ } >FLASH
+ .init_array :
+ {
+ PROVIDE_HIDDEN (__init_array_start = .);
+ KEEP (*(SORT(.init_array.*)))
+ KEEP (*(.init_array*))
+ PROVIDE_HIDDEN (__init_array_end = .);
+ } >FLASH
+ .fini_array :
+ {
+ PROVIDE_HIDDEN (__fini_array_start = .);
+ KEEP (*(SORT(.fini_array.*)))
+ KEEP (*(.fini_array*))
+ PROVIDE_HIDDEN (__fini_array_end = .);
+ } >FLASH
+
+ /* used by the startup to initialize data */
+ _sidata = LOADADDR(.data);
+
+ /* Initialized data sections goes into RAM, load LMA copy after code */
+ .data :
+ {
+ . = ALIGN(4);
+ _sdata = .; /* create a global symbol at data start */
+ *(.data) /* .data sections */
+ *(.data*) /* .data* sections */
+ *(.RamFunc) /* .RamFunc sections */
+ *(.RamFunc*) /* .RamFunc* sections */
+
+ . = ALIGN(4);
+ _edata = .; /* define a global symbol at data end */
+ } >RAM AT> FLASH
+
+ /* Uninitialized data section */
+ . = ALIGN(4);
+ .bss :
+ {
+ /* This is used by the startup in order to initialize the .bss secion */
+ _sbss = .; /* define a global symbol at bss start */
+ __bss_start__ = _sbss;
+ *(.bss)
+ *(.bss*)
+ *(COMMON)
+
+ . = ALIGN(4);
+ _ebss = .; /* define a global symbol at bss end */
+ __bss_end__ = _ebss;
+ } >RAM
+
+ /* User_heap_stack section, used to check that there is enough RAM left */
+ ._user_heap_stack :
+ {
+ . = ALIGN(8);
+ PROVIDE ( end = . );
+ PROVIDE ( _end = . );
+ . = . + _Min_Heap_Size;
+ . = . + _Min_Stack_Size;
+ . = ALIGN(8);
+ } >RAM
+
+ /* Remove information from the standard libraries */
+ /DISCARD/ :
+ {
+ libc.a ( * )
+ libm.a ( * )
+ libgcc.a ( * )
+ }
+
+ .ARM.attributes 0 : { *(.ARM.attributes) }
+}
+
+
diff --git a/hw/bsp/stm32h7/boards/waveshare_openh743i/board.h b/hw/bsp/stm32h7/boards/waveshare_openh743i/board.h
new file mode 100644
index 0000000..09442c2
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/waveshare_openh743i/board.h
@@ -0,0 +1,229 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2021
+ * Ha Thach (tinyusb.org)
+ * Benjamin Evans
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+/* ** BOARD SETUP **
+ *
+ * NOTE: This board has bad signal integrity so you may experience some problems.
+ * This setup assumes you have an openh743i-c Core and breakout board. For the HS
+ * examples it also assumes you have a waveshare USB3300 breakout board plugged
+ * into the ULPI PMOD header on the openh743i-c.
+ *
+ * UART Debugging:
+ * Due to pin conflicts in the HS configuration, this BSP uses USART3 (PD8, PD9).
+ * As such, you won't be able to use the UART to USB converter on board and will
+ * require an external UART to USB converter. You could use the waveshare FT232
+ * USB UART Board (micro) but any 3.3V UART to USB converter will be fine.
+ *
+ * Fullspeed:
+ * If VBUS sense is enabled, ensure the PA9-VBUS jumper is connected on the core
+ * board. Connect the PB6 jumper for the LED and the Wakeup - PA0 jumper for the
+ * button. Connect the USB cable to the USB connector on the core board.
+ *
+ * High Speed:
+ * Remove all jumpers from the openh743i-c (especially the USART1 jumpers as the
+ * pins conflict). Connect the PB6 jumper for the LED and the Wakeup - PA0
+ * jumper for the button.
+ *
+ * The reset pin on the ULPI PMOD port is not connected to the MCU. You'll need
+ * to solder a wire from the RST pin on the USB3300 to a pin of your choosing on
+ * the openh743i-c board (this example assumes you've used PD14 as specified with
+ * the ULPI_RST_PORT and ULPI_RST_PIN defines below).
+ *
+ * Preferably power the board using the external 5VDC jack. Connect the USB cable
+ * to the USB connector on the ULPI board. Adjust delays in this file as required.
+ *
+ * If you're having trouble, ask a question on the tinyUSB Github Discussion boards.
+ *
+ * Have fun!
+ *
+*/
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#define LED_PORT GPIOB
+#define LED_PIN GPIO_PIN_6
+#define LED_STATE_ON 1
+
+// Tamper push-button
+#define BUTTON_PORT GPIOA
+#define BUTTON_PIN GPIO_PIN_0
+#define BUTTON_STATE_ACTIVE 1
+
+// Need to change jumper setting J7 and J8 from RS-232 to STLink
+#define UART_DEV USART3
+#define UART_CLK_EN __HAL_RCC_USART3_CLK_ENABLE
+#define UART_GPIO_PORT GPIOD
+#define UART_GPIO_AF GPIO_AF7_USART3
+#define UART_TX_PIN GPIO_PIN_8
+#define UART_RX_PIN GPIO_PIN_9
+
+// VBUS Sense detection
+#define OTG_FS_VBUS_SENSE 1
+#define OTG_HS_VBUS_SENSE 0
+
+ // USB HS External PHY Pin: CLK, STP, DIR, NXT, D0-D7
+#define ULPI_PINS \
+ {GPIOA, GPIO_PIN_3 }, {GPIOA, GPIO_PIN_5 }, {GPIOB, GPIO_PIN_0 }, {GPIOB, GPIO_PIN_1 }, \
+ {GPIOB, GPIO_PIN_5 }, {GPIOB, GPIO_PIN_10}, {GPIOB, GPIO_PIN_11}, {GPIOB, GPIO_PIN_12}, \
+ {GPIOB, GPIO_PIN_13}, {GPIOC, GPIO_PIN_0 }, {GPIOC, GPIO_PIN_2 }, {GPIOC, GPIO_PIN_3 }
+
+// ULPI PHY reset pin used by walkaround
+#define ULPI_RST_PORT GPIOD
+#define ULPI_RST_PIN GPIO_PIN_14
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32h7_clock_init(void)
+{
+ RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+ RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+ RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};
+
+ __HAL_RCC_SYSCFG_CLK_ENABLE();
+
+ // Supply configuration update enable
+ HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY);
+
+ // Configure the main internal regulator output voltage
+ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0);
+
+ while (!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY))
+ {
+ }
+ // Macro to configure the PLL clock source
+ __HAL_RCC_PLL_PLLSOURCE_CONFIG(RCC_PLLSOURCE_HSE);
+
+ // Initializes the RCC Oscillators according to the specified parameters in the RCC_OscInitTypeDef structure.
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+ RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+ RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+ RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+ RCC_OscInitStruct.PLL.PLLM = 2;
+ RCC_OscInitStruct.PLL.PLLN = 240;
+ RCC_OscInitStruct.PLL.PLLP = 2;
+ RCC_OscInitStruct.PLL.PLLQ = 2;
+ RCC_OscInitStruct.PLL.PLLR = 2;
+ RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2;
+ RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOWIDE;
+ RCC_OscInitStruct.PLL.PLLFRACN = 0;
+ HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+ PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB | RCC_PERIPHCLK_USART3;
+ PeriphClkInitStruct.PLL3.PLL3M = 8;
+ PeriphClkInitStruct.PLL3.PLL3N = 336;
+ PeriphClkInitStruct.PLL3.PLL3P = 2;
+ PeriphClkInitStruct.PLL3.PLL3Q = 7;
+ PeriphClkInitStruct.PLL3.PLL3R = 2;
+ PeriphClkInitStruct.PLL3.PLL3RGE = RCC_PLL3VCIRANGE_0;
+ PeriphClkInitStruct.PLL3.PLL3VCOSEL = RCC_PLL3VCOWIDE;
+ PeriphClkInitStruct.PLL3.PLL3FRACN = 0;
+ PeriphClkInitStruct.Usart234578ClockSelection = RCC_USART234578CLKSOURCE_PLL3;
+ PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL3;
+ HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
+
+ // Initializes the CPU, AHB and APB buses clocks
+ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_D3PCLK1 | RCC_CLOCKTYPE_D1PCLK1;
+ RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+ RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1;
+ RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2;
+ RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV2;
+ RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2;
+ RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2;
+ RCC_ClkInitStruct.APB4CLKDivider = RCC_APB4_DIV2;
+ HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
+
+ __HAL_RCC_CSI_ENABLE();
+
+ // Enable SYSCFG clock mondatory for I/O Compensation Cell
+ __HAL_RCC_SYSCFG_CLK_ENABLE();
+
+ // Enables the I/O Compensation Cell
+ HAL_EnableCompensationCell();
+
+ // Enable voltage detector
+ HAL_PWREx_EnableUSBVoltageDetector();
+}
+
+static inline void timer_board_delay(TIM_HandleTypeDef* tim_hdl, uint32_t ms)
+{
+ uint32_t startMs = __HAL_TIM_GET_COUNTER(tim_hdl);
+ while ((__HAL_TIM_GET_COUNTER(tim_hdl) - startMs) < ms)
+ {
+ asm("nop"); //do nothing
+ }
+}
+
+static inline void board_stm32h7_post_init(void)
+{
+ // walkaround for reseting the ULPI PHY using Timer since systick is not
+ // available when RTOS is used.
+
+ // Init timer
+ TIM_HandleTypeDef tim2Handle;
+ TIM_ClockConfigTypeDef sClockSourceConfig = {0};
+
+ __HAL_RCC_TIM2_CLK_ENABLE();
+
+ //Assuming timer clock is running at 260Mhz this should configure the timer counter to 1000Hz
+ tim2Handle.Instance = TIM2;
+ tim2Handle.Init.Prescaler = 60000U - 1U;
+ tim2Handle.Init.CounterMode = TIM_COUNTERMODE_UP;
+ tim2Handle.Init.Period = 0xFFFFFFFFU;
+ tim2Handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV4;
+ tim2Handle.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
+ HAL_TIM_Base_Init(&tim2Handle);
+
+ sClockSourceConfig.ClockSource = TIM_CLOCKSOURCE_INTERNAL;
+ HAL_TIM_ConfigClockSource(&tim2Handle, &sClockSourceConfig);
+
+ //Start the timer
+ HAL_TIM_Base_Start(&tim2Handle);
+
+ // Reset PHY, change the delays as you see fit
+ timer_board_delay(&tim2Handle, 5U);
+ HAL_GPIO_WritePin(ULPI_RST_PORT, ULPI_RST_PIN, 1U);
+ timer_board_delay(&tim2Handle, 20U);
+ HAL_GPIO_WritePin(ULPI_RST_PORT, ULPI_RST_PIN, 0U);
+ timer_board_delay(&tim2Handle, 20U);
+
+ //Disable the timer used for delays
+ HAL_TIM_Base_Stop(&tim2Handle);
+ __HAL_RCC_TIM2_CLK_DISABLE();
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif
diff --git a/hw/bsp/stm32h7/boards/waveshare_openh743i/board.mk b/hw/bsp/stm32h7/boards/waveshare_openh743i/board.mk
new file mode 100644
index 0000000..4dfcc1c
--- /dev/null
+++ b/hw/bsp/stm32h7/boards/waveshare_openh743i/board.mk
@@ -0,0 +1,19 @@
+CFLAGS += -DSTM32H743xx -DHSE_VALUE=8000000
+
+# Default is HS port
+PORT ?= 1
+
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s
+LD_FILE = $(BOARD_PATH)/STM32H743IITX_FLASH.ld
+
+# Use Timer module for ULPI PHY reset
+CFLAGS += -DHAL_TIM_MODULE_ENABLED
+SRC_C += \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim.c \
+ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_tim_ex.c
+
+# For flash-jlink target
+JLINK_DEVICE = stm32h743ii
+
+# flash target using jlink
+flash: flash-jlink
\ No newline at end of file