diff --git a/hw/bsp/stm32f207nucleo/stm32f207nucleo.c b/hw/bsp/stm32f207nucleo/stm32f207nucleo.c
new file mode 100644
index 0000000..619c90d
--- /dev/null
+++ b/hw/bsp/stm32f207nucleo/stm32f207nucleo.c
@@ -0,0 +1,213 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "../board.h"
+
+#include "stm32f2xx_hal.h"
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void OTG_FS_IRQHandler(void)
+{
+  tud_int_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+
+#define LED_PORT              GPIOB
+#define LED_PIN               GPIO_PIN_14
+#define LED_STATE_ON          1
+
+#define BUTTON_PORT           GPIOC
+#define BUTTON_PIN            GPIO_PIN_13
+#define BUTTON_STATE_ACTIVE   1
+
+
+// enable all LED, Button, Uart, USB clock
+static void all_rcc_clk_enable(void)
+{
+  __HAL_RCC_GPIOA_CLK_ENABLE();  // USB D+, D-
+  __HAL_RCC_GPIOB_CLK_ENABLE();  // LED
+  __HAL_RCC_GPIOC_CLK_ENABLE();  // Button
+}
+
+/**
+  * @brief  System Clock Configuration
+  *         The system Clock is configured as follow :
+  *            System Clock source            = PLL (HSE)
+  *            SYSCLK(Hz)                     = 120000000
+  *            HCLK(Hz)                       = 120000000
+  *            AHB Prescaler                  = 1
+  *            APB1 Prescaler                 = 4
+  *            APB2 Prescaler                 = 2
+  *            HSE Frequency(Hz)              = 8000000
+  *            PLL_M                          = HSE_VALUE/1000000
+  *            PLL_N                          = 240
+  *            PLL_P                          = 2
+  *            PLL_Q                          = 5
+  *            VDD(V)                         = 3.3
+  *            Flash Latency(WS)              = 3
+  * @param  None
+  * @retval None
+  */
+void SystemClock_Config(void)
+{
+  RCC_ClkInitTypeDef RCC_ClkInitStruct;
+  RCC_OscInitTypeDef RCC_OscInitStruct;
+
+  /* Enable HSE Oscillator and activate PLL with HSE as source */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+  RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+  RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000;
+  RCC_OscInitStruct.PLL.PLLN = 240;
+  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+  RCC_OscInitStruct.PLL.PLLQ = 5;
+  HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
+     clocks dividers */
+  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3);
+}
+
+void board_init(void)
+{
+  SystemClock_Config();
+  
+  #if CFG_TUSB_OS  == OPT_OS_NONE
+  // 1ms tick timer
+  SysTick_Config(SystemCoreClock / 1000);
+  #endif
+
+
+  all_rcc_clk_enable();
+
+  GPIO_InitTypeDef  GPIO_InitStruct;
+
+  // LED
+  GPIO_InitStruct.Pin = LED_PIN;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_PULLUP;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+  HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+  board_led_write(false);
+
+  // Button
+  GPIO_InitStruct.Pin = BUTTON_PIN;
+  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+  GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+  HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+
+  /* Configure DM DP Pins */
+  GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
+  GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /* Configure VBUS Pin */
+  GPIO_InitStruct.Pin = GPIO_PIN_9;
+  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /* Configure ID pin */
+  GPIO_InitStruct.Pin = GPIO_PIN_10;
+  GPIO_InitStruct.Mode = GPIO_MODE_AF_OD;
+  GPIO_InitStruct.Pull = GPIO_PULLUP;
+  GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /* Enable USB FS Clocks */
+  __HAL_RCC_USB_OTG_FS_CLK_ENABLE();
+
+  // Enable VBUS sense (B device) via pin PA9
+  USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_NOVBUSSENS;
+  USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBUSBSEN;
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+  HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
+}
+
+uint32_t board_button_read(void)
+{
+  return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+  (void) buf; (void) len;
+  return 0;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+  (void) buf; (void) len;
+  return 0;
+}
+
+#if CFG_TUSB_OS  == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+  system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+  return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+  asm("bkpt");
+}
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}