diff --git a/hw/bsp/stm32f1/boards/stm32f103_bluepill/STM32F103X8_FLASH.ld b/hw/bsp/stm32f1/boards/stm32f103_bluepill/STM32F103X8_FLASH.ld
new file mode 100644
index 0000000..ca18049
--- /dev/null
+++ b/hw/bsp/stm32f1/boards/stm32f103_bluepill/STM32F103X8_FLASH.ld
@@ -0,0 +1,167 @@
+/*
+*****************************************************************************
+**
+**  File        : STM32F103XB_FLASH.ld
+**
+**  Abstract    : Linker script for STM32F103xB Device with
+**                128KByte FLASH, 20KByte RAM
+**
+**                Set heap size, stack size and stack location according
+**                to application requirements.
+**
+**                Set memory bank area and size if external memory is used.
+**
+**  Target      : STMicroelectronics STM32
+**
+**
+**  Distribution: The file is distributed as is, without any warranty
+**                of any kind.
+**
+**  (c)Copyright Ac6.
+**  You may use this file as-is or modify it according to the needs of your
+**  project. Distribution of this file (unmodified or modified) is not
+**  permitted. Ac6 permit registered System Workbench for MCU users the
+**  rights to distribute the assembled, compiled & linked contents of this
+**  file as part of an application binary file, provided that it is built
+**  using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20004FFF;    /* end of RAM */
+
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200;      /* required amount of heap  */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+FLASH (rx)      : ORIGIN = 0x08000000, LENGTH = 64K
+RAM (xrw)       : ORIGIN = 0x20000000, LENGTH = 20K
+}
+
+/* Define output sections */
+SECTIONS
+{
+  /* The startup code goes first into FLASH */
+  .isr_vector :
+  {
+    . = ALIGN(4);
+    KEEP(*(.isr_vector)) /* Startup code */
+    . = ALIGN(4);
+  } >FLASH
+
+  /* The program code and other data goes into FLASH */
+  .text :
+  {
+    . = ALIGN(4);
+    *(.text)           /* .text sections (code) */
+    *(.text*)          /* .text* sections (code) */
+    *(.glue_7)         /* glue arm to thumb code */
+    *(.glue_7t)        /* glue thumb to arm code */
+    *(.eh_frame)
+
+    KEEP (*(.init))
+    KEEP (*(.fini))
+
+    . = ALIGN(4);
+    _etext = .;        /* define a global symbols at end of code */
+  } >FLASH
+
+  /* Constant data goes into FLASH */
+  .rodata :
+  {
+    . = ALIGN(4);
+    *(.rodata)         /* .rodata sections (constants, strings, etc.) */
+    *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
+    . = ALIGN(4);
+  } >FLASH
+
+  .ARM.extab   : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+  .ARM : {
+    __exidx_start = .;
+    *(.ARM.exidx*)
+    __exidx_end = .;
+  } >FLASH
+
+  .preinit_array     :
+  {
+    PROVIDE_HIDDEN (__preinit_array_start = .);
+    KEEP (*(.preinit_array*))
+    PROVIDE_HIDDEN (__preinit_array_end = .);
+  } >FLASH
+  .init_array :
+  {
+    PROVIDE_HIDDEN (__init_array_start = .);
+    KEEP (*(SORT(.init_array.*)))
+    KEEP (*(.init_array*))
+    PROVIDE_HIDDEN (__init_array_end = .);
+  } >FLASH
+  .fini_array :
+  {
+    PROVIDE_HIDDEN (__fini_array_start = .);
+    KEEP (*(SORT(.fini_array.*)))
+    KEEP (*(.fini_array*))
+    PROVIDE_HIDDEN (__fini_array_end = .);
+  } >FLASH
+
+  /* used by the startup to initialize data */
+  _sidata = LOADADDR(.data);
+
+  /* Initialized data sections goes into RAM, load LMA copy after code */
+  .data : 
+  {
+    . = ALIGN(4);
+    _sdata = .;        /* create a global symbol at data start */
+    *(.data)           /* .data sections */
+    *(.data*)          /* .data* sections */
+
+    . = ALIGN(4);
+    _edata = .;        /* define a global symbol at data end */
+  } >RAM AT> FLASH
+
+  
+  /* Uninitialized data section */
+  . = ALIGN(4);
+  .bss :
+  {
+    /* This is used by the startup in order to initialize the .bss secion */
+    _sbss = .;         /* define a global symbol at bss start */
+    __bss_start__ = _sbss;
+    *(.bss)
+    *(.bss*)
+    *(COMMON)
+
+    . = ALIGN(4);
+    _ebss = .;         /* define a global symbol at bss end */
+    __bss_end__ = _ebss;
+  } >RAM
+
+  /* User_heap_stack section, used to check that there is enough RAM left */
+  ._user_heap_stack :
+  {
+    . = ALIGN(8);
+    PROVIDE ( end = . );
+    PROVIDE ( _end = . );
+    . = . + _Min_Heap_Size;
+    . = . + _Min_Stack_Size;
+    . = ALIGN(8);
+  } >RAM
+
+  
+
+  /* Remove information from the standard libraries */
+  /DISCARD/ :
+  {
+    libc.a ( * )
+    libm.a ( * )
+    libgcc.a ( * )
+  }
+
+  .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32f1/boards/stm32f103_bluepill/board.h b/hw/bsp/stm32f1/boards/stm32f103_bluepill/board.h
new file mode 100644
index 0000000..57a607e
--- /dev/null
+++ b/hw/bsp/stm32f1/boards/stm32f103_bluepill/board.h
@@ -0,0 +1,92 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+// LED
+#define LED_PORT              GPIOC
+#define LED_PIN               GPIO_PIN_13
+#define LED_STATE_ON          0
+
+// Button
+#define BUTTON_PORT           GPIOA
+#define BUTTON_PIN            GPIO_PIN_0
+#define BUTTON_STATE_ACTIVE   1
+
+// UART
+//#define UART_DEV              USART1
+//#define UART_CLK_EN           __HAL_RCC_USART1_CLK_ENABLE
+//#define UART_GPIO_PORT        GPIOA
+//#define UART_GPIO_AF          GPIO_AF1_USART1
+//#define UART_TX_PIN           GPIO_PIN_9
+//#define UART_RX_PIN           GPIO_PIN_10
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32f1_clock_init(void)
+{
+  RCC_ClkInitTypeDef clkinitstruct = {0};
+  RCC_OscInitTypeDef oscinitstruct = {0};
+  RCC_PeriphCLKInitTypeDef rccperiphclkinit = {0};
+
+  /* Enable HSE Oscillator and activate PLL with HSE as source */
+  oscinitstruct.OscillatorType  = RCC_OSCILLATORTYPE_HSE;
+  oscinitstruct.HSEState        = RCC_HSE_ON;
+  oscinitstruct.HSEPredivValue  = RCC_HSE_PREDIV_DIV1;
+  oscinitstruct.PLL.PLLMUL      = RCC_PLL_MUL9;
+  oscinitstruct.PLL.PLLState    = RCC_PLL_ON;
+  oscinitstruct.PLL.PLLSource   = RCC_PLLSOURCE_HSE;
+  HAL_RCC_OscConfig(&oscinitstruct);
+
+  /* USB clock selection */
+  rccperiphclkinit.PeriphClockSelection = RCC_PERIPHCLK_USB;
+  rccperiphclkinit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5;
+  HAL_RCCEx_PeriphCLKConfig(&rccperiphclkinit);
+
+  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+  clkinitstruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+  clkinitstruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  clkinitstruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  clkinitstruct.APB1CLKDivider = RCC_HCLK_DIV2;
+  clkinitstruct.APB2CLKDivider = RCC_HCLK_DIV1;
+  HAL_RCC_ClockConfig(&clkinitstruct, FLASH_LATENCY_2);
+}
+
+static inline void board_vbus_sense_init(void)
+{
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif /* BOARD_H_ */
diff --git a/hw/bsp/stm32f1/boards/stm32f103_bluepill/board.mk b/hw/bsp/stm32f1/boards/stm32f103_bluepill/board.mk
new file mode 100644
index 0000000..db64b3a
--- /dev/null
+++ b/hw/bsp/stm32f1/boards/stm32f103_bluepill/board.mk
@@ -0,0 +1,11 @@
+CFLAGS += -DSTM32F103xB -DHSE_VALUE=8000000U -DCFG_EXAMPLE_VIDEO_READONLY
+
+# All source paths should be relative to the top level.
+LD_FILE = $(BOARD_PATH)/STM32F103X8_FLASH.ld
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f103xb.s
+
+# For flash-jlink target
+JLINK_DEVICE = stm32f103c8
+
+# flash target ROM bootloader
+flash: flash-dfu-util
diff --git a/hw/bsp/stm32f1/boards/stm32f103_mini_2/STM32F103XC_FLASH.ld b/hw/bsp/stm32f1/boards/stm32f103_mini_2/STM32F103XC_FLASH.ld
new file mode 100644
index 0000000..da40d1e
--- /dev/null
+++ b/hw/bsp/stm32f1/boards/stm32f103_mini_2/STM32F103XC_FLASH.ld
@@ -0,0 +1,167 @@
+/*
+*****************************************************************************
+**
+**  File        : STM32F103XB_FLASH.ld
+**
+**  Abstract    : Linker script for STM32F103xB Device with
+**                128KByte FLASH, 20KByte RAM
+**
+**                Set heap size, stack size and stack location according
+**                to application requirements.
+**
+**                Set memory bank area and size if external memory is used.
+**
+**  Target      : STMicroelectronics STM32
+**
+**
+**  Distribution: The file is distributed as is, without any warranty
+**                of any kind.
+**
+**  (c)Copyright Ac6.
+**  You may use this file as-is or modify it according to the needs of your
+**  project. Distribution of this file (unmodified or modified) is not
+**  permitted. Ac6 permit registered System Workbench for MCU users the
+**  rights to distribute the assembled, compiled & linked contents of this
+**  file as part of an application binary file, provided that it is built
+**  using the System Workbench for MCU toolchain.
+**
+*****************************************************************************
+*/
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Highest address of the user mode stack */
+_estack = 0x20004FFF;    /* end of RAM */
+
+/* Generate a link error if heap and stack don't fit into RAM */
+_Min_Heap_Size = 0x200;      /* required amount of heap  */
+_Min_Stack_Size = 0x400; /* required amount of stack */
+
+/* Specify the memory areas */
+MEMORY
+{
+FLASH (rx)      : ORIGIN = 0x08000000, LENGTH = 256K
+RAM (xrw)       : ORIGIN = 0x20000000, LENGTH = 48K
+}
+
+/* Define output sections */
+SECTIONS
+{
+  /* The startup code goes first into FLASH */
+  .isr_vector :
+  {
+    . = ALIGN(4);
+    KEEP(*(.isr_vector)) /* Startup code */
+    . = ALIGN(4);
+  } >FLASH
+
+  /* The program code and other data goes into FLASH */
+  .text :
+  {
+    . = ALIGN(4);
+    *(.text)           /* .text sections (code) */
+    *(.text*)          /* .text* sections (code) */
+    *(.glue_7)         /* glue arm to thumb code */
+    *(.glue_7t)        /* glue thumb to arm code */
+    *(.eh_frame)
+
+    KEEP (*(.init))
+    KEEP (*(.fini))
+
+    . = ALIGN(4);
+    _etext = .;        /* define a global symbols at end of code */
+  } >FLASH
+
+  /* Constant data goes into FLASH */
+  .rodata :
+  {
+    . = ALIGN(4);
+    *(.rodata)         /* .rodata sections (constants, strings, etc.) */
+    *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
+    . = ALIGN(4);
+  } >FLASH
+
+  .ARM.extab   : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH
+  .ARM : {
+    __exidx_start = .;
+    *(.ARM.exidx*)
+    __exidx_end = .;
+  } >FLASH
+
+  .preinit_array     :
+  {
+    PROVIDE_HIDDEN (__preinit_array_start = .);
+    KEEP (*(.preinit_array*))
+    PROVIDE_HIDDEN (__preinit_array_end = .);
+  } >FLASH
+  .init_array :
+  {
+    PROVIDE_HIDDEN (__init_array_start = .);
+    KEEP (*(SORT(.init_array.*)))
+    KEEP (*(.init_array*))
+    PROVIDE_HIDDEN (__init_array_end = .);
+  } >FLASH
+  .fini_array :
+  {
+    PROVIDE_HIDDEN (__fini_array_start = .);
+    KEEP (*(SORT(.fini_array.*)))
+    KEEP (*(.fini_array*))
+    PROVIDE_HIDDEN (__fini_array_end = .);
+  } >FLASH
+
+  /* used by the startup to initialize data */
+  _sidata = LOADADDR(.data);
+
+  /* Initialized data sections goes into RAM, load LMA copy after code */
+  .data : 
+  {
+    . = ALIGN(4);
+    _sdata = .;        /* create a global symbol at data start */
+    *(.data)           /* .data sections */
+    *(.data*)          /* .data* sections */
+
+    . = ALIGN(4);
+    _edata = .;        /* define a global symbol at data end */
+  } >RAM AT> FLASH
+
+  
+  /* Uninitialized data section */
+  . = ALIGN(4);
+  .bss :
+  {
+    /* This is used by the startup in order to initialize the .bss secion */
+    _sbss = .;         /* define a global symbol at bss start */
+    __bss_start__ = _sbss;
+    *(.bss)
+    *(.bss*)
+    *(COMMON)
+
+    . = ALIGN(4);
+    _ebss = .;         /* define a global symbol at bss end */
+    __bss_end__ = _ebss;
+  } >RAM
+
+  /* User_heap_stack section, used to check that there is enough RAM left */
+  ._user_heap_stack :
+  {
+    . = ALIGN(8);
+    PROVIDE ( end = . );
+    PROVIDE ( _end = . );
+    . = . + _Min_Heap_Size;
+    . = . + _Min_Stack_Size;
+    . = ALIGN(8);
+  } >RAM
+
+  
+
+  /* Remove information from the standard libraries */
+  /DISCARD/ :
+  {
+    libc.a ( * )
+    libm.a ( * )
+    libgcc.a ( * )
+  }
+
+  .ARM.attributes 0 : { *(.ARM.attributes) }
+}
diff --git a/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.h b/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.h
new file mode 100644
index 0000000..bedce7f
--- /dev/null
+++ b/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.h
@@ -0,0 +1,92 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+// LED
+#define LED_PORT              GPIOA
+#define LED_PIN               GPIO_PIN_8
+#define LED_STATE_ON          0
+
+// Button
+#define BUTTON_PORT           GPIOA
+#define BUTTON_PIN            GPIO_PIN_0
+#define BUTTON_STATE_ACTIVE   1
+
+// UART
+//#define UART_DEV              USART1
+//#define UART_CLK_EN           __HAL_RCC_USART1_CLK_ENABLE
+//#define UART_GPIO_PORT        GPIOA
+//#define UART_GPIO_AF          GPIO_AF1_USART1
+//#define UART_TX_PIN           GPIO_PIN_9
+//#define UART_RX_PIN           GPIO_PIN_10
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32f1_clock_init(void)
+{
+  RCC_ClkInitTypeDef clkinitstruct = {0};
+  RCC_OscInitTypeDef oscinitstruct = {0};
+  RCC_PeriphCLKInitTypeDef rccperiphclkinit = {0};
+
+  /* Enable HSE Oscillator and activate PLL with HSE as source */
+  oscinitstruct.OscillatorType  = RCC_OSCILLATORTYPE_HSE;
+  oscinitstruct.HSEState        = RCC_HSE_ON;
+  oscinitstruct.HSEPredivValue  = RCC_HSE_PREDIV_DIV1;
+  oscinitstruct.PLL.PLLMUL      = RCC_PLL_MUL9;
+  oscinitstruct.PLL.PLLState    = RCC_PLL_ON;
+  oscinitstruct.PLL.PLLSource   = RCC_PLLSOURCE_HSE;
+  HAL_RCC_OscConfig(&oscinitstruct);
+
+  /* USB clock selection */
+  rccperiphclkinit.PeriphClockSelection = RCC_PERIPHCLK_USB;
+  rccperiphclkinit.UsbClockSelection = RCC_USBCLKSOURCE_PLL_DIV1_5;
+  HAL_RCCEx_PeriphCLKConfig(&rccperiphclkinit);
+
+  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
+  clkinitstruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
+  clkinitstruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  clkinitstruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  clkinitstruct.APB1CLKDivider = RCC_HCLK_DIV2;
+  clkinitstruct.APB2CLKDivider = RCC_HCLK_DIV1;
+  HAL_RCC_ClockConfig(&clkinitstruct, FLASH_LATENCY_2);
+}
+
+static inline void board_vbus_sense_init(void)
+{
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif /* BOARD_H_ */
diff --git a/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.mk b/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.mk
new file mode 100644
index 0000000..eeda870
--- /dev/null
+++ b/hw/bsp/stm32f1/boards/stm32f103_mini_2/board.mk
@@ -0,0 +1,11 @@
+CFLAGS += -DSTM32F103xB -DHSE_VALUE=8000000U
+
+# All source paths should be relative to the top level.
+LD_FILE = $(BOARD_PATH)/STM32F103XC_FLASH.ld
+SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f103xb.s
+
+# For flash-jlink target
+JLINK_DEVICE = stm32f103rc
+
+# flash target ROM bootloader
+flash: flash-jlink
diff --git a/hw/bsp/stm32f1/family.c b/hw/bsp/stm32f1/family.c
new file mode 100644
index 0000000..8fcf9eb
--- /dev/null
+++ b/hw/bsp/stm32f1/family.c
@@ -0,0 +1,167 @@
+/* 
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "stm32f1xx_hal.h"
+#include "bsp/board.h"
+#include "board.h"
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USB_HP_IRQHandler(void)
+{
+  tud_int_handler(0);
+}
+
+void USB_LP_IRQHandler(void)
+{
+  tud_int_handler(0);
+}
+
+void USBWakeUp_IRQHandler(void)
+{
+  tud_int_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+
+void board_init(void)
+{
+  board_stm32f1_clock_init();
+  
+  // Enable All GPIOs clocks
+  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_GPIOB_CLK_ENABLE();
+  __HAL_RCC_GPIOC_CLK_ENABLE();
+  __HAL_RCC_GPIOD_CLK_ENABLE();
+
+#if CFG_TUSB_OS  == OPT_OS_NONE
+  // 1ms tick timer
+  SysTick_Config(SystemCoreClock / 1000);
+
+#elif CFG_TUSB_OS == OPT_OS_FREERTOS
+  // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
+  NVIC_SetPriority(USB_HP_CAN1_TX_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
+  NVIC_SetPriority(USB_LP_CAN1_RX0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
+  NVIC_SetPriority(USBWakeUp_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
+#endif
+  
+  // LED
+  GPIO_InitTypeDef  GPIO_InitStruct;
+  GPIO_InitStruct.Pin = LED_PIN;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = LED_STATE_ON ? GPIO_PULLDOWN : GPIO_PULLUP;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+  HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct);
+
+  // Button
+  GPIO_InitStruct.Pin = BUTTON_PIN;
+  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+  GPIO_InitStruct.Pull = BUTTON_STATE_ACTIVE ? GPIO_PULLDOWN : GPIO_PULLUP;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+  HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct);
+
+  // USB Pins
+  // Configure USB DM and DP pins.
+  GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12);
+  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
+  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  // USB Clock enable
+  __HAL_RCC_USB_CLK_ENABLE();
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+  HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
+}
+
+uint32_t board_button_read(void)
+{
+  return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN);
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+  (void) buf; (void) len;
+  return 0;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+  (void) buf; (void) len;
+  return 0;
+}
+
+#if CFG_TUSB_OS  == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler (void)
+{
+  system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+  return system_ticks;
+}
+#endif
+
+void HardFault_Handler (void)
+{
+  asm("bkpt");
+}
+
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  Reports the name of the source file and the source line number
+  *         where the assert_param error has occurred.
+  * @param  file: pointer to the source file name
+  * @param  line: assert_param error line source number
+  * @retval None
+  */
+void assert_failed(char *file, uint32_t line)
+{ 
+  /* USER CODE BEGIN 6 */
+  /* User can add his own implementation to report the file name and line number,
+     tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
+  /* USER CODE END 6 */
+}
+#endif /* USE_FULL_ASSERT */
+
+// Required by __libc_init_array in startup code if we are compiling using
+// -nostdlib/-nostartfiles.
+void _init(void)
+{
+
+}
diff --git a/hw/bsp/stm32f1/family.mk b/hw/bsp/stm32f1/family.mk
new file mode 100644
index 0000000..3fb2e6e
--- /dev/null
+++ b/hw/bsp/stm32f1/family.mk
@@ -0,0 +1,45 @@
+ST_FAMILY = f1
+DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
+
+ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY)
+ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver
+
+include $(TOP)/$(BOARD_PATH)/board.mk
+
+CFLAGS += \
+  -flto \
+  -mthumb \
+  -mabi=aapcs \
+  -mcpu=cortex-m3 \
+  -mfloat-abi=soft \
+  -nostdlib -nostartfiles \
+  -DCFG_TUSB_MCU=OPT_MCU_STM32F1
+
+# mcu driver cause following warnings
+#CFLAGS += -Wno-error=unused-parameter
+
+# All source paths should be relative to the top level.
+SRC_C += \
+  src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c \
+  $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \
+  $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c
+
+INC += \
+  $(TOP)/$(BOARD_PATH) \
+  $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
+  $(TOP)/$(ST_CMSIS)/Include \
+  $(TOP)/$(ST_HAL_DRIVER)/Inc
+
+# For freeRTOS port source
+FREERTOS_PORT = ARM_CM3
+
+# For flash-jlink target
+JLINK_DEVICE = stm32f103c8
+
+# flash target ROM bootloader
+flash-dfu-util: $(BUILD)/$(PROJECT).bin
+	dfu-util -R -a 0 --dfuse-address 0x08000000 -D $<
diff --git a/hw/bsp/stm32f1/stm32f1xx_hal_conf.h b/hw/bsp/stm32f1/stm32f1xx_hal_conf.h
new file mode 100644
index 0000000..a4a3f30
--- /dev/null
+++ b/hw/bsp/stm32f1/stm32f1xx_hal_conf.h
@@ -0,0 +1,379 @@
+/**
+  ******************************************************************************
+  * @file    USB_Device/HID_Standalone/Inc/stm32f1xx_hal_conf.h
+  * @author  MCD Application Team
+  * @brief   HAL configuration template file.
+  *          This file should be copied to the application folder and renamed
+  *          to stm32f1xx_hal_conf.h.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_CONF_H
+#define __STM32F1xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+  * @brief This is the list of modules to be used in the HAL driver 
+  */
+#define HAL_MODULE_ENABLED
+/* #define HAL_ADC_MODULE_ENABLED */
+/* #define HAL_CAN_MODULE_ENABLED */
+/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
+#define HAL_CORTEX_MODULE_ENABLED */
+/* #define HAL_CRC_MODULE_ENABLED */
+/* #define HAL_DAC_MODULE_ENABLED */
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_EXTI_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_GPIO_MODULE_ENABLED
+/* #define HAL_I2C_MODULE_ENABLED */
+/* #define HAL_I2S_MODULE_ENABLED */
+/* #define HAL_IRDA_MODULE_ENABLED */
+/* #define HAL_IWDG_MODULE_ENABLED */
+/* #define HAL_NOR_MODULE_ENABLED */
+/* #define HAL_PCCARD_MODULE_ENABLED */
+#define HAL_PCD_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+/* #define HAL_RTC_MODULE_ENABLED */
+/* #define HAL_SD_MODULE_ENABLED */
+/* #define HAL_SDRAM_MODULE_ENABLED */
+/* #define HAL_SMARTCARD_MODULE_ENABLED */
+/* #define HAL_SPI_MODULE_ENABLED */
+/* #define HAL_SRAM_MODULE_ENABLED */
+/* #define HAL_TIM_MODULE_ENABLED */
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED */
+/* #define HAL_WWDG_MODULE_ENABLED */
+
+/* ########################## Oscillator Values adaptation ####################*/
+/**
+  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSE is used as system clock source, directly or through the PLL).  
+  */
+#if !defined  (HSE_VALUE) 
+#if defined(USE_STM3210C_EVAL)
+  #define HSE_VALUE    25000000U /*!< Value of the External oscillator in Hz */
+#else
+  #define HSE_VALUE    8000000U /*!< Value of the External oscillator in Hz */
+#endif
+#endif /* HSE_VALUE */
+
+#if !defined  (HSE_STARTUP_TIMEOUT)
+  #define HSE_STARTUP_TIMEOUT    100U      /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal High Speed oscillator (HSI) value.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSI is used as system clock source, directly or through the PLL). 
+  */
+#if !defined  (HSI_VALUE)
+  #define HSI_VALUE              8000000U  /*!< Value of the Internal oscillator in Hz */
+#endif /* HSI_VALUE */
+
+/**
+  * @brief Internal Low Speed oscillator (LSI) value.
+  */
+#if !defined  (LSI_VALUE) 
+ #define LSI_VALUE               40000U    /*!< LSI Typical Value in Hz */
+#endif /* LSI_VALUE */                     /*!< Value of the Internal Low Speed oscillator in Hz
+                                                The real value may vary depending on the variations
+                                                in voltage and temperature. */
+
+/**
+  * @brief External Low Speed oscillator (LSE) value.
+  *        This value is used by the UART, RTC HAL module to compute the system frequency
+  */
+#if !defined  (LSE_VALUE)
+ #define LSE_VALUE               32768U    /*!< Value of the External oscillator in Hz*/
+#endif /* LSE_VALUE */
+
+#if !defined  (LSE_STARTUP_TIMEOUT)
+  #define LSE_STARTUP_TIMEOUT    5000U     /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+   ===  you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+  * @brief This is the HAL system configuration section
+  */     
+#define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
+#define  TICK_INT_PRIORITY            0x00U /*!< tick interrupt priority */
+#define  USE_RTOS                     0U
+#define  PREFETCH_ENABLE              1U
+
+#define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
+#define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
+#define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
+#define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
+#define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
+#define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
+#define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
+#define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
+#define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
+#define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
+#define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
+#define  USE_HAL_PCCARD_REGISTER_CALLBACKS      0U /* PCCARD register callback disabled    */
+#define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
+#define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
+#define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
+#define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
+#define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
+#define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
+#define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
+#define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
+#define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
+#define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
+#define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */
+
+/* ########################## Assert Selection ############################## */
+/**
+  * @brief Uncomment the line below to expanse the "assert_param" macro in the 
+  *        HAL drivers code
+  */
+/* #define USE_FULL_ASSERT    1U */
+
+/* ################## Ethernet peripheral configuration ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0   2U
+#define MAC_ADDR1   0U
+#define MAC_ADDR2   0U
+#define MAC_ADDR3   0U
+#define MAC_ADDR4   0U
+#define MAC_ADDR5   0U
+
+/* Definition of the Ethernet driver buffers size and count */   
+#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
+#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
+#define ETH_RXBUFNB                    8U                  /* 8 Rx buffers of size ETH_RX_BUF_SIZE  */
+#define ETH_TXBUFNB                    4U                  /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
+
+/* Section 2: PHY configuration section */
+
+/* DP83848 PHY Address*/ 
+#define DP83848_PHY_ADDRESS             0x01U
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 
+#define PHY_RESET_DELAY                 0x000000FFU
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY                0x00000FFFU
+
+#define PHY_READ_TO                     0x0000FFFFU
+#define PHY_WRITE_TO                    0x0000FFFFU
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR                         ((uint16_t)0x0000)  /*!< Transceiver Basic Control Register   */
+#define PHY_BSR                         ((uint16_t)0x0001)  /*!< Transceiver Basic Status Register    */
+ 
+#define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
+#define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
+#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
+#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
+#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
+#define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
+#define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
+
+#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
+#define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
+#define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
+  
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR                          ((uint16_t)0x0010)  /*!< PHY status register Offset                      */
+#define PHY_MICR                        ((uint16_t)0x0011)  /*!< MII Interrupt Control Register                  */
+#define PHY_MISR                        ((uint16_t)0x0012)  /*!< MII Interrupt Status and Misc. Control Register */
+ 
+#define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
+#define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
+#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
+
+#define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
+#define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
+
+#define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
+#define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC                     1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+  * @brief Include module's header file 
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+ #include "stm32f1xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+ #include "stm32f1xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+   
+#ifdef HAL_EXTI_MODULE_ENABLED
+  #include "stm32f1xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+  #include "stm32f1xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+   
+#ifdef HAL_CAN_MODULE_ENABLED
+ #include "stm32f1xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+  #include "Legacy/stm32f1xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+ #include "stm32f1xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+ #include "stm32f1xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+ #include "stm32f1xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+ #include "stm32f1xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+ #include "stm32f1xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+  #include "stm32f1xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+  #include "stm32f1xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f1xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f1xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f1xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f1xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f1xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+ #include "stm32f1xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */ 
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f1xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */  
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+ #include "stm32f1xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */     
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f1xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f1xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f1xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f1xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f1xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f1xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f1xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f1xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr: If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed. 
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+  #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+  void assert_failed(uint8_t* file, uint32_t line);
+#else
+  #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */    
+    
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/